Welcome to the Veson Nautical Knowledge Base. In the Help Center, you can view the same articles and contact support as needed.

IMOS - Bunker Planning and Estimated Consumption

In Bunker Planning, bunker prices are proposed based on purchase history, but you can change them, set up your initial quantities, and set up calculation methods for each fuel type. Fuel use is calculated by port, and you can enter quantities and prices for any bunkers you plan to receive.

To open the Bunker Planning form, do one of the following:

  • On the Estimate column or details toolbar, click  or  and then click Bunker Planning.

  • On the Estimate details fuel grid, either click  or right-click a line item, and then click Details.

  • On the Estimate P&L panel, under Expenses, click the Bunkers line item.

Depending on the Vessel Type in the Estimate, columns can also appear for Sea Consumption for heating, cooling, and reliquefaction, and Port Consumption for heating, cooling, and reliquefaction, as well as IGS consumption.

  • Sea Consumption is calculated based on the specified consumption rate for the speed associated with the sea leg.

  • Port Consumption is calculated based on the time used for loading or discharging, basis SHINC, at the Load or Discharge consumption rate specified for the vessel. Additional time in port is calculated basis the vessel-specified Idle consumption rate. This additional time is Turn Time and time spent in port during weekend clauses. In addition, you can add extra time in port: The related columns are XP and Dem, which also count as Idle time.

  • For LNG vessels, the LNG detail tab includes additional fields for **OV Estimates only (not **TO Estimates).

    • Max Load - (Vessel Capacity m3 * Filling Limit %) - Initial Bunkers m3

    • Max Discharge - Loaded/Received Qty m3 - Total LNG Consumption m3

    • To back-calculate the optimal discharge quantity based on heel, right-click a discharge port and then click Calculate Disch Qty based on Heel.


      Enter the Heel desired upon arrival and then click Calculate. To save the calculated Discharge Quantity, click Save.

  • For Bulk carriers, there is an option for each port call to indicate whether the vessel will be using its own cranes. If not, it consumes at the Idle consumption rate.

 

Optimize Liftings for Cargo

For a type **OV voyage, you can optimize liftings based on bunker prices at fueling ports specified in the Voyage Estimate Itinerary. You can also take into account the freight rate of one of the cargoes on the Voyage Estimate to determine if it is more beneficial to lift more bunkers in place of that cargo or vice versa.

On the Bunker Planning form, do the following:

  1. Select the Optimize Liftings for Cargo check box.

    • To subtract the freight rate of one Cargo on the itinerary from the bunker price at the next port before the most advantageous fueling port is determined, in the field next to the check box, select a Cargo with Freight Type F.

  2. Enter a bunker Price for each port at which you want to lift bunkers.

  3. Enter an End Quantity greater than or equal to the safety Margin of the vessel.

The Initial Quantity is taken into account and the amount of fuel needed across all voyage legs calculates. When Prices are entered, Receive quantities automatically populate at the ports with the lowest price. Quantities are calculated such that the vessel arrives at the terminating port with a quantity equal to the specified End Quantity.

  • If there are multiple fueling ports (indicated by prices entered) in the itinerary, the Receive quantities are automatically populated with the amount of bunkers needed to arrive at the first fueling port so that the ROBs are equal to the safety margin of the vessel. Then, at the second fueling port, the amount of bunkers are populated such that the quantity upon arrival at the terminating port is equal to the End Quantity specified.

  • If you manually enter a lifting quantity, that amount appears blue and is not overridden when the calculation is run again.

  • The optimizer calculates in real time; that is, Receive quantities automatically adjust when you change prices.

  • The optimizer no longer calculates after the Voyage Estimate is fixed; it is for planning purposes only.

Use Scrubbers

When the Use Scrubbers check box is selected, low sulfur bunkers are not used for at-sea consumption within ECA zones. Instead, high sulfur ("H"-type in the Vessel) bunkers is consumed. In-port consumption still adheres to Vessel/Fuel Zone bunker configuration if a given port is within an ECA zone.

Fuel Zones

For Estimates that are not already using Fuel Zones to calculate bunker consumption and have unsailed ports, a Use Fuel Zones button appears in the lower left corner. To recalculate estimated bunker consumption and cost based on information entered in Fuel Zones in the Data Center, click Use Fuel Zones.

If you have configured a Fuel Zone Set, you can select it, rather than the Default set, at the bottom of this form.

Why Isn't my Estimate showing consuming correctly?

There are a few places you can check to find out why a vessel isn't consuming as planned.

  • Open the bunker estimate and check the Fuel Zone Set

 

  • Check the Vessel Details to confirm your fuel types are configured correctly. (Vessel Fuel Zone Set can be entered here)

 

  • Within the voyage bunkers, make sure there is enough Primary fuel to complete the voyage. If there is not, the system with calculating with a backup fuel unless there is not enough fuel for the backup Fuel to complete the voyage or the disable backup fuel checkbox has been selected. In this case, the system will have the Primary fuel consume the entire voyage and the backup fuel quantity will be untouched. This is based on the assumption that a bunker lifting will happen, clearing the need to use the backup fuel for the voyage. 

 

  • Is this a copy of another estimate? If so the estimate will consume based on the fuel zones configuration during the time of the creation of the original estimate. We suggest making a new estimate or enabling the configuration flag Recalc Distances on Estimate Copy.

 

  • Have changes been made to the Fuel Zone configuration since the creation of the estimate? Estimates will calculate fuel consumption based on the configuration at that creation of the Estimate, new changes will not be shown. 

  • If an initial FIFO queue is populated for the estimate, editing the initial bunker price will now ask users if they want to replace the initial FIFO inventory with a flat price.

 

 

 

Name/Flag

Description

Name/Flag

Description

Enable Legacy IFO Top Off Calc
CFGEnableLegacyIFOTopOffCalc

For LNG vessels, relates to the calculation of the amount of IFO (or other designated "FOE" fuel type) needed in order to accelerate to a given speed higher than the NBOG speed when in dual-fuel mode. When this config flag is enabled, this amount is calculated as the difference between (a) the IFO consumption at actual speed and (b) the FOE equivalent of the LNG consumption at the NBOG speed. When this config flag is disabled or by default, this amount is calculated as the difference between (a) the IFO consumption at actual speed and (b) the IFO consumption at NBOG speed.

Enable Voyage Estimate Init Bunker Queue
CFGEnableVoyestInitBunkerQueue

When enabled, Estimates allow multiple initial lots for each bunker type, similar to the Voyage Manager. On the Bunker Planning form, the Initial Quantity field label becomes a link that, when clicked, opens the Initial Bunkers form. These lots will be defaulted from open positions, TC In delivery, and in-progress voyages. When bunker consumption exceeds the available inventory for a certain fuel type, the end price for that fuel type is used to calculate bunker costs. If an initial FIFO queue is populated for the estimate, editing the initial bunker price will now ask users if they want to replace the initial FIFO inventory with a flat price if this configuration flag is enabled.

Enable Scrubber Type
CFGEnableScrubberType

When enabled, a scrubber drop-down menu appears on the Port, Voyage Bunkers, Bunker Planning, and Vessel forms accessed through an Estimate. On the Port and Vessel forms, the drop-down menu reflects scrubber values allowed at the port and equipped in the vessel. On the Voyage Estimate and Voyage, it reflects the scrubber type used for bunker calculations. On the Vessel form, the “Use Scrubbers” check box is replaced with the new “Scrubber Type” drop-down menu. The Fuel Zones form has two tabs to support “Scrubber” and “Non-Scrubber” configurations. These new options facilitate bunker calculations to use the IMO 2020 regulations.

 

 

Still need help? Visit the Veson Nautical Help Center.

Copyright © 2017-2024 Veson Nautical LLC All Rights Reserved - Privacy Notice | End User Terms of Use